HAS MY POOL PUMP BURNED OUT
Has my pool pump burned out?(tank pump repairs)
How to know whether your pool pump has burned out
My pool water has turned green and I have seen that the pool pump isn't working.
What I can do?
To begin with, you need to check if there is any assurance component inside the electrical board, for example, the differential or the motor insurance, other than that it has fallen.
In the event that you find any of these things that have fallen, continue to reassemble it again and check if the pump works.
In the event that all the assurances are re-amassed and the pump doesn't work, you know, put on your electrician's overalls and get the opportunity to work.
Above all else, be cautious with electricity
Be extremely cautious when handling electrical boards, you generally need to give close consideration to where you touch that you don't get a stun.
In the event that you don't have an analyzer (multimeter) you can get a basic voltage analyzer, the kind that they sell in any home improvement shop, and even in the "Chinese".
These voltage analyzers are exceptionally easy to utilize, they have two hints, which we put in contact with the two terminals where there should be voltage and a few LEDs light up indicating what voltage is coming.
Where do we start?
Open the association spread that the pump has, check the starting capacitor, to check whether it looks burned.
In the event that the starting capacitor has burned out, purchase another one of a similar limit (ordinarily, on the pump nameplate it indicates which capacitor it uses) and afterward start it again in manual mode to check whether the pump begins.
In the event that the capacitor has all the earmarks of being unharmed, check with your analyzer to check whether the voltage is reaching the pump terminals.(zodiac chlorinator)
In the event that strain shows up, it implies that something happens to the pump, if the pressure doesn't show up you can enjoy a reprieve and without a doubt, your pump isn't burned and the breakdown will be cheaper than you think.
Voltage arrives at the pump however doesn't begin
On the off chance that when you attempt to begin the pump it makes clamor yet the turbine doesn't begin to turn, all things considered, the starting capacitor needs more limit, get one of a similar limit and supplant it. You attempt again and with a touch of karma, you will have comprehended it.
In the event that you've changed the condenser it despite everything won't start, before you surrender and think that the starter loop is burned out, you can expel the body of the per-channel and check whether there is any impediment in the turbine that is preventing the engine from turning it.
The pump doesn't get the pressure
In the wake of checking that the pump has no voltage, you should check in which part of the circuit, from the input through the differential, through the motor watchman and ending with the contactor, the conductivity is lost.
It begins by checking the voltage input to the electrical board, typically it is a differential. Watch that voltage is available at the input and output of the differential with your analyzer.
In the event that there is no voltage, you should go to the overall image of the house to check whether there is any magneto-warm or differential down.
On the off chance that the voltage arrives at the differential, continue checking in the following point, which is regularly the motor watchman. You continue to do likewise, you should check both the input and the output of the motor gatekeeper that there is the voltage.
On the off chance that the voltage comes out of the motor gatekeeper, you go to the following component, which will be the contactor. The contactor could be supposed to be a transfer however with more posts. This contactor is enacted through a 220v sign that originates from the move (manual switch or clock) to the contactor curl (A1 and A2).
On the off chance that you watch that voltage enters the contactor and its curl being enacted, (220v reaches somewhere in the range of A1 and A2) there is no voltage at the shafts where the pump is associated, it is truly conceivable that Some of your contacts are harmed, so find a comparable one and supplant it.
As should be obvious, it is an occupation of checking parts, this implies when the pool pump stops working it isn't generally on the grounds that its winding has burned. Once in awhile we can "luck out" and it is some other segment that has fizzled and normally the repair is a lot cheaper than repairing or replacing the pool pump.
On the off chance that you have come this far and your pump despite everything doesn't work or you don't set out to get into these aubergines, don't stop for a second to get in touch with us. We are here to support you.(Chlorinator spare parts )